page 1 of 5 the big deal ? ultra-high ip3, +43 dbm typ. ? medium power, +28.7dbm typ. ? excellent noise figure, 1.1 db typ. product overview PHA-13HLN+ (rohs compliant) is an advanced wideband amplifer fabricated using e-phemt technology and offers extremely high dynamic range over a broad frequency range and with low noise fgure. in addition, the PHA-13HLN+ has good input and output return loss over a broad frequency range. PHA-13HLN+ is enclosed in a sot-89 package and has very good thermal performance. key features PHA-13HLN+ 50 ? 1mhz to 1 ghz feature advantages broad band: 1mhz to 1ghz broadband covering primary wireless communications bands: vhf, uhf, cellular extremely high ip3 38.4 dbm typical at 1mhz 43 dbm typical at 0.5ghz the PHA-13HLN+ matches industry leading ip3 performance relative to device size and power consumption. the combination of the design and e-phemt structure provides enhanced linearity over a broad frequency range as evidence in the ip3 being approximately 15 db above the p1db point. this feature makes this amplifer ideal for use in: ? driver amplifers for complex waveform up converter paths ? drivers in linearized transmit systems ? secondary amplifers in ultra-high dynamic range receivers low noise figure 1.1 db at 0.5 ghz enables lower system noise fgure performance high p1db 28.7 dbm at 500 mhz high p1db, high oip3, low nf results in a very dynamic range preventing amplifer saturation under strong interfering signals. it can also be used to drive mixers requiring high drive sot-89 package ultra high dynamic range monolithic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
page 2 of 5 product features ?high ip3, 43 dbm typ. at 0.5ghz ?gain, 22.7 db typ. at 0.5 ghz ?high pout, p1db 28.7 dbm typ. at 0.5ghz ?low noise fgure, 1.1 db at 0.5 ghz typical applications ?base station infrastructure ?catv ?cellular rev. or m159854 PHA-13HLN+ mcl ny 171129 general description PHA-13HLN+ (rohs compliant) is an advanced wideband amplifer fabricated using e-phemt technology and offers extremely high dynamic range over a broad frequency range and with low noise fgure. in addi - tion, the PHA-13HLN+ has good input and output return loss over a broad frequency range. PHA-13HLN+ is enclosed in a sot-89 package and has very good thermal performance. simplifed schematic and pin description function pin number description rf in 1 rf input rf-out and dc-in 3 rf output and dc bias gnd 2,4 connections to ground. case style: df782 PHA-13HLN+ 1mhz to 1 ghz rf-in rf-out and dc-in gnd 3 rf-out & dc-in 2 ground 1 rf-in 4 ultra high dynamic range monolithic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications
page 3 of 5 electrical specifcations at 25c, 50 ? , unless noted 1 absolute maximum ratings (4) parameter condition (mhz) vd=8v 1 units min. typ. max. frequency range 1 1000 mhz gain 1 22.4 25.0 27.4 db 20 24.3 250 23.0 500 20.4 22.7 25.0 1000 20.4 input return loss 1 10.8 db 20 15.8 250 16.7 500 17.5 1000 10.5 output return loss 1 11.2 db 20 18.8 250 17.7 500 29.4 1000 9.0 reverse isolation 500 26.3 db output power @1 db compression 1 26.2 dbm 20 27.3 250 28.4 500 28.7 1000 27.4 output ip3 (2) 1 38.4 dbm 20 41.7 250 43.5 500 40.0 43.0 1000 42.2 noise figure 1 3.0 db 20 1.2 250 1.1 500 1.1 1000 1.4 device operating voltage 8.0 v device operating current 234.1 251 ma device current variation vs. temperature (3) -100.6 a/c device current variation vs voltage 0.0155 ma/mv thermal resistance, junction-to-ground lead junction-to-ground lead at 85c stage temperature 23.3 c/w PHA-13HLN+ parameter ratings operating temperature (ground lead) -40c to 95c storage temperature -65c to 150c power dissipation 3.3 w 5 input power (cw) +21 dbm (5 minutes max) 6 +10 dbm (continuous) for 1-10 mhz +11 dbm (continuous) for 10-1000 mhz dc voltage on pin 3 10v 4. permanent damage may occur if any of these limits are exceeded. electrical maximum ratings are not intended for continuous normal operation. 5. up to 85c, derate linearly to 2.5 w at 95c. 6. upt 85c, derate linearly to 18 dbm at 95c. 1. measured on mini-circuits characterization test board tb-969-13hln+. see characterization test circuit (fig. 1) 2. tested at pout= 0 dbm / tone. 3. (current at 85c current at -45c)/130 monolithic e-phemt mmic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
page 4 of 5 fig 1. block diagram of test circuit used for characterization. (dut soldered on mini-circuits characterization test board tb-969-13hln+) gain, return loss, output power at 1db compression (p1db), output ip3 (oip3) and noise fgure measured using agilents n5242a pna-x microwave network analyzer. conditions: 1. gain and return loss: pin= -25dbm 2. output ip3 (oip3): two tones, spaced 0.5 mhz apart, 0 dbm/ tone at output. characterization test / recommended application circuit PHA-13HLN+ marking may contain other features or characters for internal lot control product marking ph23 a monolithic e-phemt mmic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com pha - 13hln+ monolithic e - phemt mmic amplifier mini - ci r cuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235 - 0003 (718) 934 - 4500 sales@minicircuits.com page 4 of 5 characterization test /recommended application circuit fig 1. block diagram of test circuit used for characterization. (dut soldered on mini - circuits characterization test board tb - 969- 13hln +) gain, return loss, output p ower at 1db compression (p1 db) , output ip3 (oip3) and noise figure measured using agilents n5242a pna - x microwave network analyzer. conditions: 1. gain and return loss: pin= - 25dbm 2. output ip3 (oip3): two tones, spaced 1 mhz apart, 0 dbm/ t one at output. product marking marking may contain other features or characters for internal lot control ph23
page 5 of 5 PHA-13HLN+ esd rating human body model (hbm): class 1b (pass 500 v) in accordance with ansi/esd stm 5.1 - 2001 msl rating moisture sensitivity: msl1 in accordance with ipc/jedec j-std-020d additional detailed technical information additional information is available on our dash board. to access this information click here performance data data table swept graphs s-parameter (s2p files) data set (.zip fle) case style df782 (sot 89) plastic package, exposed paddle lead fnish: matt-tin tape & reel f55 standard quantities available on reel 7 reels with 20, 50, 100, 200, 500 or 1k devices suggested layout for pcb design pl-523 evaluation board tb-969-13hln+ environmental ratings env08t9 visual inspection electrical test sam analysis refow 3 cycles, 260c soak 85c/85rh 168 hours bake at 125c, 24 hours visual inspection electrical test sam analysis start msl test flow chart stop monolithic e-phemt mmic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
|
